Minggu, 20 September 2009
21.58 | 
Posted by
Windy Computer
Manual steps to recover a corrupted registry that prevents Windows XP from starting
====================================
The procedure that this article describes uses Recovery Console and System Restore. This article also lists all the required steps in specific order to make sure that the process is fully completed. When you finish this procedure, the system returns to a state very close to the state before the problem occurred. If you have ever run NTBackup and completed a system state backup, you do not have to follow the procedures in parts two and three. You can go to part four.
Part one
In part one, you start the Recovery Console, create a temporary folder, back up the existing registry files to a new location, delete the registry files at their existing location, and then copy the registry files from the repair folder to the System32\Config folder. When you have finished this procedure, a registry is created that you can use to start Windows XP. This registry was created and saved during the initial setup of Windows XP. Therefore any changes and settings that occurred after the Setup program was finished are lost.
To complete part one, follow these steps:
1. Insert the Windows XP startup disk into the floppy disk drive, or insert the Windows XP CD-ROM into the CD-ROM drive, and then restart the computer.
Click to select any options that are required to start the computer from the CD-ROM drive if you are prompted to do so.
2. When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
3. If you have a dual-boot or multiple-boot computer, select the installation that you want to access from the Recovery Console.
4. When you are prompted to do so, type the Administrator password. If the administrator password is blank, just press ENTER.
5. At the Recovery Console command prompt, type the following lines, pressing ENTER after you type each line:
md tmp
copy c:\windows\system32\config\system c:\windows\tmp\system.bak
copy c:\windows\system32\config\software c:\windows\tmp\software.bak
copy c:\windows\system32\config\sam c:\windows\tmp\sam.bak
copy c:\windows\system32\config\security c:\windows\tmp\security.bak
copy c:\windows\system32\config\default c:\windows\tmp\default.bak
delete c:\windows\system32\config\system
delete c:\windows\system32\config\software
delete c:\windows\system32\config\sam
delete c:\windows\system32\config\security
delete c:\windows\system32\config\default
copy c:\windows\repair\system c:\windows\system32\config\system
copy c:\windows\repair\software c:\windows\system32\config\software
copy c:\windows\repair\sam c:\windows\system32\config\sam
copy c:\windows\repair\security c:\windows\system32\config\security
copy c:\windows\repair\default c:\windows\system32\config\default
6. Type exit to quit Recovery Console. Your computer will restart.
Note This procedure assumes that Windows XP is installed to the C:\Windows folder. Make sure to change C:\Windows to the appropriate windows_folder if it is a different location.
If you have access to another computer, to save time, you can copy the text in step five, and then create a text file called "Regcopy1.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy1.txt
With the batch command in Recovery Console, you can process all the commands in a text file sequentially. When you use the batch command, you do not have to manually type as many commands.
Part two
To complete the procedure described in this section, you must be logged on as an administrator, or an administrative user (a user who has an account in the Administrators group). If you are using Windows XP Home Edition, you can log on as an administrative user. If you log on as an administrator, you must first start Windows XP Home Edition in Safe mode. To start the Windows XP Home Edition computer in Safe mode, follow these steps.
Note Print these instructions before you continue. You cannot view these instructions after you restart the computer in Safe Mode. If you use the NTFS file system, also print the instructions from Knowledge Base article KB309531. Step 7 contains a reference to the article.
1. Click Start, click Shut Down (or click Turn Off Computer), click Restart, and then click OK (or click Restart).
2. Press the F8 key.
On a computer that is configured to start to multiple operating systems, you can press F8 when you see the Startup menu.
3. Use the arrow keys to select the appropriate Safe mode option, and then press ENTER.
4. If you have a dual-boot or multiple-boot system, use the arrow keys to select the installation that you want to access, and then press ENTER.
In part two, you copy the registry files from their backed up location by using System Restore. This folder is not available in Recovery Console and is generally not visible during typical usage. Before you start this procedure, you must change several settings to make the folder visible:
1. Start Windows Explorer.
2. On the Tools menu, click Folder options.
3. Click the View tab.
4. Under Hidden files and folders, click to select Show hidden files and folders, and then click to clear the Hide protected operating system files (Recommended) check box.
5. Click Yes when the dialog box that confirms that you want to display these files appears.
6. Double-click the drive where you installed Windows XP to display a list of the folders. If is important to click the correct drive.
7. Open the System Volume Information folder. This folder is unavailable and appears dimmed because it is set as a super-hidden folder.
Note This folder contains one or more _restore {GUID} folders such as "_restore{87BD3667-3246-476B-923F-F86E30B3E7F8}".
Note You may receive the following error message:
C:\System Volume Information is not accessible. Access is denied.
If you receive this message, see the following Microsoft Knowledge Base article to gain access to this folder and continue with the procedure:
309531 (http://support.microsoft.com/kb/309531/) How to gain access to the System Volume Information folder
8. Open a folder that was not created at the current time. You may have to click Details on the View menu to see when these folders were created. There may be one or more folders starting with "RPx under this folder. These are restore points.
9. Open one of these folders to locate a Snapshot subfolder. The following path is an example of a folder path to the Snapshot folder:
C:\System Volume Information\_restore{D86480E3-73EF-47BC-A0EB-A81BE6EE3ED8}\RP1\Snapshot
10. From the Snapshot folder, copy the following files to the C:\Windows\Tmp folder:
• _REGISTRY_USER_.DEFAULT
• _REGISTRY_MACHINE_SECURITY
• _REGISTRY_MACHINE_SOFTWARE
• _REGISTRY_MACHINE_SYSTEM
• _REGISTRY_MACHINE_SAM
11. Rename the files in the C:\Windows\Tmp folder as follows:
• Rename _REGISTRY_USER_.DEFAULT to DEFAULT
• Rename _REGISTRY_MACHINE_SECURITY to SECURITY
• Rename _REGISTRY_MACHINE_SOFTWARE to SOFTWARE
• Rename _REGISTRY_MACHINE_SYSTEM to SYSTEM
• Rename _REGISTRY_MACHINE_SAM to SAM
These files are the backed up registry files from System Restore. Because you used the registry file that the Setup program created, this registry does not know that these restore points exist and are available. A new folder is created with a new GUID under System Volume Information and a restore point is created that includes a copy of the registry files that were copied during part one. Therefore, it is important not to use the most current folder, especially if the time stamp on the folder is the same as the current time.
The current system configuration is not aware of the previous restore points. You must have a previous copy of the registry from a previous restore point to make the previous restore points available again.
The registry files that were copied to the Tmp folder in the C:\Windows folder are moved to make sure that the files are available under Recovery Console. You must use these files to replace the registry files currently in the C:\Windows\System32\Config folder. By default, Recovery Console has limited folder access and cannot copy files from the System Volume folder.
Note The procedure described in this section assumes that you are running your computer with the FAT32 file system. For more information about how to access the System Volume Information Folder with the NTFS file system, click the following article number to view the article in the Microsoft Knowledge Base:
309531 (http://support.microsoft.com/kb/309531/) How to gain access to the System Volume Information folder
Part Three
In part three, you delete the existing registry files, and then copy the System Restore Registry files to the C:\Windows\System32\Config folder:
1. Start Recovery Console.
2. At the command prompt, type the following lines, pressing ENTER after you type each line:
del c:\windows\system32\config\sam
del c:\windows\system32\config\security
del c:\windows\system32\config\software
del c:\windows\system32\config\default
del c:\windows\system32\config\system
copy c:\windows\tmp\software c:\windows\system32\config\software
copy c:\windows\tmp\system c:\windows\system32\config\system
copy c:\windows\tmp\sam c:\windows\system32\config\sam
copy c:\windows\tmp\security c:\windows\system32\config\security
copy c:\windows\tmp\default c:\windows\system32\config\default
Note Some of these command lines may be wrapped for readability.
3. Type exit to quit Recovery Console. Your computer restarts.
Note This procedure assumes that Windows XP is installed to the C:\Windows folder. Make sure to change C:\Windows to the appropriate windows_folder if it is a different location.
If you have access to another computer, to save time, you can copy the text in step two, and then create a text file called "Regcopy2.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy2.txt
Part Four
1. Click Start, and then click All Programs.
2. Click Accessories, and then click System Tools.
3. Click System Restore, and then click Restore to a previous RestorePoint.
====================================
The procedure that this article describes uses Recovery Console and System Restore. This article also lists all the required steps in specific order to make sure that the process is fully completed. When you finish this procedure, the system returns to a state very close to the state before the problem occurred. If you have ever run NTBackup and completed a system state backup, you do not have to follow the procedures in parts two and three. You can go to part four.
Part one
In part one, you start the Recovery Console, create a temporary folder, back up the existing registry files to a new location, delete the registry files at their existing location, and then copy the registry files from the repair folder to the System32\Config folder. When you have finished this procedure, a registry is created that you can use to start Windows XP. This registry was created and saved during the initial setup of Windows XP. Therefore any changes and settings that occurred after the Setup program was finished are lost.
To complete part one, follow these steps:
1. Insert the Windows XP startup disk into the floppy disk drive, or insert the Windows XP CD-ROM into the CD-ROM drive, and then restart the computer.
Click to select any options that are required to start the computer from the CD-ROM drive if you are prompted to do so.
2. When the "Welcome to Setup" screen appears, press R to start the Recovery Console.
3. If you have a dual-boot or multiple-boot computer, select the installation that you want to access from the Recovery Console.
4. When you are prompted to do so, type the Administrator password. If the administrator password is blank, just press ENTER.
5. At the Recovery Console command prompt, type the following lines, pressing ENTER after you type each line:
md tmp
copy c:\windows\system32\config\system c:\windows\tmp\system.bak
copy c:\windows\system32\config\software c:\windows\tmp\software.bak
copy c:\windows\system32\config\sam c:\windows\tmp\sam.bak
copy c:\windows\system32\config\security c:\windows\tmp\security.bak
copy c:\windows\system32\config\default c:\windows\tmp\default.bak
delete c:\windows\system32\config\system
delete c:\windows\system32\config\software
delete c:\windows\system32\config\sam
delete c:\windows\system32\config\security
delete c:\windows\system32\config\default
copy c:\windows\repair\system c:\windows\system32\config\system
copy c:\windows\repair\software c:\windows\system32\config\software
copy c:\windows\repair\sam c:\windows\system32\config\sam
copy c:\windows\repair\security c:\windows\system32\config\security
copy c:\windows\repair\default c:\windows\system32\config\default
6. Type exit to quit Recovery Console. Your computer will restart.
Note This procedure assumes that Windows XP is installed to the C:\Windows folder. Make sure to change C:\Windows to the appropriate windows_folder if it is a different location.
If you have access to another computer, to save time, you can copy the text in step five, and then create a text file called "Regcopy1.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy1.txt
With the batch command in Recovery Console, you can process all the commands in a text file sequentially. When you use the batch command, you do not have to manually type as many commands.
Part two
To complete the procedure described in this section, you must be logged on as an administrator, or an administrative user (a user who has an account in the Administrators group). If you are using Windows XP Home Edition, you can log on as an administrative user. If you log on as an administrator, you must first start Windows XP Home Edition in Safe mode. To start the Windows XP Home Edition computer in Safe mode, follow these steps.
Note Print these instructions before you continue. You cannot view these instructions after you restart the computer in Safe Mode. If you use the NTFS file system, also print the instructions from Knowledge Base article KB309531. Step 7 contains a reference to the article.
1. Click Start, click Shut Down (or click Turn Off Computer), click Restart, and then click OK (or click Restart).
2. Press the F8 key.
On a computer that is configured to start to multiple operating systems, you can press F8 when you see the Startup menu.
3. Use the arrow keys to select the appropriate Safe mode option, and then press ENTER.
4. If you have a dual-boot or multiple-boot system, use the arrow keys to select the installation that you want to access, and then press ENTER.
In part two, you copy the registry files from their backed up location by using System Restore. This folder is not available in Recovery Console and is generally not visible during typical usage. Before you start this procedure, you must change several settings to make the folder visible:
1. Start Windows Explorer.
2. On the Tools menu, click Folder options.
3. Click the View tab.
4. Under Hidden files and folders, click to select Show hidden files and folders, and then click to clear the Hide protected operating system files (Recommended) check box.
5. Click Yes when the dialog box that confirms that you want to display these files appears.
6. Double-click the drive where you installed Windows XP to display a list of the folders. If is important to click the correct drive.
7. Open the System Volume Information folder. This folder is unavailable and appears dimmed because it is set as a super-hidden folder.
Note This folder contains one or more _restore {GUID} folders such as "_restore{87BD3667-3246-476B-923F-F86E30B3E7F8}".
Note You may receive the following error message:
C:\System Volume Information is not accessible. Access is denied.
If you receive this message, see the following Microsoft Knowledge Base article to gain access to this folder and continue with the procedure:
309531 (http://support.microsoft.com/kb/309531/) How to gain access to the System Volume Information folder
8. Open a folder that was not created at the current time. You may have to click Details on the View menu to see when these folders were created. There may be one or more folders starting with "RPx under this folder. These are restore points.
9. Open one of these folders to locate a Snapshot subfolder. The following path is an example of a folder path to the Snapshot folder:
C:\System Volume Information\_restore{D86480E3-73EF-47BC-A0EB-A81BE6EE3ED8}\RP1\Snapshot
10. From the Snapshot folder, copy the following files to the C:\Windows\Tmp folder:
• _REGISTRY_USER_.DEFAULT
• _REGISTRY_MACHINE_SECURITY
• _REGISTRY_MACHINE_SOFTWARE
• _REGISTRY_MACHINE_SYSTEM
• _REGISTRY_MACHINE_SAM
11. Rename the files in the C:\Windows\Tmp folder as follows:
• Rename _REGISTRY_USER_.DEFAULT to DEFAULT
• Rename _REGISTRY_MACHINE_SECURITY to SECURITY
• Rename _REGISTRY_MACHINE_SOFTWARE to SOFTWARE
• Rename _REGISTRY_MACHINE_SYSTEM to SYSTEM
• Rename _REGISTRY_MACHINE_SAM to SAM
These files are the backed up registry files from System Restore. Because you used the registry file that the Setup program created, this registry does not know that these restore points exist and are available. A new folder is created with a new GUID under System Volume Information and a restore point is created that includes a copy of the registry files that were copied during part one. Therefore, it is important not to use the most current folder, especially if the time stamp on the folder is the same as the current time.
The current system configuration is not aware of the previous restore points. You must have a previous copy of the registry from a previous restore point to make the previous restore points available again.
The registry files that were copied to the Tmp folder in the C:\Windows folder are moved to make sure that the files are available under Recovery Console. You must use these files to replace the registry files currently in the C:\Windows\System32\Config folder. By default, Recovery Console has limited folder access and cannot copy files from the System Volume folder.
Note The procedure described in this section assumes that you are running your computer with the FAT32 file system. For more information about how to access the System Volume Information Folder with the NTFS file system, click the following article number to view the article in the Microsoft Knowledge Base:
309531 (http://support.microsoft.com/kb/309531/) How to gain access to the System Volume Information folder
Part Three
In part three, you delete the existing registry files, and then copy the System Restore Registry files to the C:\Windows\System32\Config folder:
1. Start Recovery Console.
2. At the command prompt, type the following lines, pressing ENTER after you type each line:
del c:\windows\system32\config\sam
del c:\windows\system32\config\security
del c:\windows\system32\config\software
del c:\windows\system32\config\default
del c:\windows\system32\config\system
copy c:\windows\tmp\software c:\windows\system32\config\software
copy c:\windows\tmp\system c:\windows\system32\config\system
copy c:\windows\tmp\sam c:\windows\system32\config\sam
copy c:\windows\tmp\security c:\windows\system32\config\security
copy c:\windows\tmp\default c:\windows\system32\config\default
Note Some of these command lines may be wrapped for readability.
3. Type exit to quit Recovery Console. Your computer restarts.
Note This procedure assumes that Windows XP is installed to the C:\Windows folder. Make sure to change C:\Windows to the appropriate windows_folder if it is a different location.
If you have access to another computer, to save time, you can copy the text in step two, and then create a text file called "Regcopy2.txt" (for example). To use this file, run the following command when you start in Recovery Console:
batch regcopy2.txt
Part Four
1. Click Start, and then click All Programs.
2. Click Accessories, and then click System Tools.
3. Click System Restore, and then click Restore to a previous RestorePoint.
Senin, 03 Agustus 2009
15.21 |
Posted by
Windy Computer
Nokia
1. *#30# : Menampilkan “private number” yang menghubungi anda.
2. *#73# : Mereset timer dan high score game. (hanya pada ponsel tertentu).
3. *#7780# : Untuk mengembalikan ke settingan pabrik / Soft reset.
4. *#2820# : Alamat IP perangkat Bluetooth.
5. Xx# : Akses cepat ke nomer atau nama pada address book anda.
6. *#0000# : Menampilkan versi resmi ponsel, baris pertama menunjukkan versi softwarenya, lalu baris kedua menampilkan tanggal pembuatan software dan baris ketiga menunjukkan tipe kompresi software yang digunakan.
7. *#9999# : Sebagai alternatif apabila kode *#0000# tidak berfungsi.
8. *#06# : Melihat nomor IMEI ( International Mobile Equipment Identity ).
9. *#21# : Mengecek nomer pengalihan “ All calls “
10. *#43# : Mengecek status “Call waiting”.
11. *#67705646# : Mengganti operator logo pada 3310 dan 3330,
12. *#746025625# : Menampilkan status SIM Clock. Jika ponsel anda mendukung fitur penghematan energi, akan keluar tulisan “ SIM Clock Allowed”, artinya anda akan mendapat waktu stand by yang lebih.
13. *#92702689# : Menampilkan : 1. Serial Number, 2. Date Made, 3. Purchase date, 4. Date of last repair , 5. Transfer user data. Pada beberapa ponsel setelah menggunakan fitur ini anda harus merestart ponsel.
Sony Ericsson
1. *#06# : Melihat IMEi
2. *#0000# : Mereset kembali ke bahasa Inggris
3. >*<<*<* : Service menu, menampilkan versi software ponsel,. Tekan tombol Yes berulang kali untuk melihat semua data software dan tekan > untk melihat semua teks yang terdapat pada ponsel.
4. <**< : Untuk mengunci SIM Card.
=====================================
PHILIPS SECRET CODES
PHILLIPS:
*#06# -> Displays imei
*#2254*# -> Status Register: C, BS, RR, MMI, CREAT
*#2255*# -> Activate & Deactivate the "DEBUG CALL"-
*#2558*# -> The time in days, hours & minutes you are connected to the net
*#2562*# -> Not Clear; the phone reconnects to the net
*#2565*# -> Not Clear; Warmstart?
*#3333*# -> (NO) BLOCKING - list (15 Items)
*#2377*# -> "BEER": not clear, the phone waits a random time and reconnects to the net,
sometimes the phone makes a reset
*#3377*# -> Init, Flags, SIM LCK
*#3353*# -> Resets the (NO) BLOCKING - list
*#7378*# -> Name, Length, SIM phase
*#7489*# -> SECURITY CODE
*#7693*# -> You can activate & deactivate the SLEEP MODE
(when deactivated the battery will go down)
*#7787*# -> Not clear: SPURIOUS INTERRUPT
*#7948*# -> SWITCH OFF: not clear; it is a timer or something
*#8463*# -> Some information about the SLEEP MODE
Philips Genie (TCD838)
*#2337*# -> Will activate the beep signal when the cellphone reconnected to the net
Service Codes
Alcatel
Master Codes
- 25228352
- 25228353
- 83227423 (TH3/4,BH4,BF5,BG3,BF3/4..)
###337*07# - master reset (with SIM)
###847# - factory reset (with SIM)
###728# - factory reset (with SIM)
Alcatel 835 formating - **0102#
Samsung
*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu (X100)
Philips
#20021208# ok - 630 without SIM (erase flash)
*#7728*# - RSAV DONE
*#3849*# - ??? reboot
*#3851*# - ??? reboot
Philips 568 *01763*737381# - reset
Pantech
*01763*737381# - master reset (user data, user code) without SIM
*01763*8371# - SW version
*01763*6371# - UNLOCK
*01763*3641# - Menu
Panasonic
*01763*737381# - master reset (user data, user code) A100, A101, A102,G50, G51, G70,
GD55..
*369#(*) - MENU
7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power on - SW version (GD75, GD67, GD87..)
LG
2945#*# - service menu (code reset)(W3000 G5300 C1200 G7100...)
2945#(*)- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service Menu
B1300 *+pwr, 1,5,9 Service Menu
Security Removing Code For Lg 8110,8120.
47328545454#
Or
277634#*#
Sony-Ericsson
> * < < * < * - Service menu
< * * < - Lock menu
VK Mobile
*#79# - SW version
*#85*364# (*) - hold menu
855855# without SIM (VG107)
85558555#(*)-hold
4268#(*)-hold (VG207)
Voxtel
0124 - master code
0718#(*)- hold - menu (ST11, SC10, V100 without SIM)
4268#(*)- hold - show code (ST11, SC10 without SIM)
*789(#)- hold - menu (V50, V300, RX100 without SIM)
Motorola
(T190, T191, T205) master code
- 19980722
- 20010903
**********
P2K test menu:
*#06#, menu, menu, 048263*
Test comands:
32*116*1*0*0 - read phone code
32*118*1*0*0 - read security code
18*0 - factory reset, phone code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version
Hard reset MPX200, MPX220 - blue button + power on
Nokia
*#7370925538# (valet code reset) 6230
*#746025625# [*#sim0clock#]
*#92702689# [*#war0anty#]
Fly Bird
S688 - #*301#02# send - with SIM
menu:
7 - 10 - ok,
#*8000#, #*3676# (reboot repair)
V09, S1180 - *, 3 times down, 3 times up - service menu
Enol
*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version
Maxon
*#9922# - menu, reset (without SIM)
*#9900# - Software Version
*#9901# - Software Version (PBatch)
S60 Siries (SX1, 6600, N-Gage..)
*#7780# - factory default
*#7370# - full factory defaults (all user data reset)
SX1 formating - * + # + power on
6600 formating - 3 + * + send + power on
Sendo X1 formating - 5 + power on
Mitsubishi
*65512890 (*-hold) format FFS (Eclipse)
* 3926 - (*-hold) test mode
* 5806 - (*-hold) SW version
*(hold) 787090 - trium 320 unlock menu
Huawei (cdma)
MASTER SECURITY CODE
-309296
-3092
-9296
Pantech HX-550C (cdma)
Full reset (phone code reset)- ##03*934#9367*192#397#7412569746 PWR,
after reset - ##27732726 PWR and select "with uim"
=========================================================
Nokia Master Code Calculator, master code buat ngebuka security code
http://filecargo.com/dw.php?id=1178989260&/1/mastercode.exe
masukan imei, trus keluar dech 10 digit master code nya...
imei 15 digit bisa diliat di belakang casing dibawah battery...
ato dengan menekan *#06#
1. *#30# : Menampilkan “private number” yang menghubungi anda.
2. *#73# : Mereset timer dan high score game. (hanya pada ponsel tertentu).
3. *#7780# : Untuk mengembalikan ke settingan pabrik / Soft reset.
4. *#2820# : Alamat IP perangkat Bluetooth.
5. Xx# : Akses cepat ke nomer atau nama pada address book anda.
6. *#0000# : Menampilkan versi resmi ponsel, baris pertama menunjukkan versi softwarenya, lalu baris kedua menampilkan tanggal pembuatan software dan baris ketiga menunjukkan tipe kompresi software yang digunakan.
7. *#9999# : Sebagai alternatif apabila kode *#0000# tidak berfungsi.
8. *#06# : Melihat nomor IMEI ( International Mobile Equipment Identity ).
9. *#21# : Mengecek nomer pengalihan “ All calls “
10. *#43# : Mengecek status “Call waiting”.
11. *#67705646# : Mengganti operator logo pada 3310 dan 3330,
12. *#746025625# : Menampilkan status SIM Clock. Jika ponsel anda mendukung fitur penghematan energi, akan keluar tulisan “ SIM Clock Allowed”, artinya anda akan mendapat waktu stand by yang lebih.
13. *#92702689# : Menampilkan : 1. Serial Number, 2. Date Made, 3. Purchase date, 4. Date of last repair , 5. Transfer user data. Pada beberapa ponsel setelah menggunakan fitur ini anda harus merestart ponsel.
Sony Ericsson
1. *#06# : Melihat IMEi
2. *#0000# : Mereset kembali ke bahasa Inggris
3. >*<<*<* : Service menu, menampilkan versi software ponsel,. Tekan tombol Yes berulang kali untuk melihat semua data software dan tekan > untk melihat semua teks yang terdapat pada ponsel.
4. <**< : Untuk mengunci SIM Card.
=====================================
PHILIPS SECRET CODES
PHILLIPS:
*#06# -> Displays imei
*#2254*# -> Status Register: C, BS, RR, MMI, CREAT
*#2255*# -> Activate & Deactivate the "DEBUG CALL"-
*#2558*# -> The time in days, hours & minutes you are connected to the net
*#2562*# -> Not Clear; the phone reconnects to the net
*#2565*# -> Not Clear; Warmstart?
*#3333*# -> (NO) BLOCKING - list (15 Items)
*#2377*# -> "BEER": not clear, the phone waits a random time and reconnects to the net,
sometimes the phone makes a reset
*#3377*# -> Init, Flags, SIM LCK
*#3353*# -> Resets the (NO) BLOCKING - list
*#7378*# -> Name, Length, SIM phase
*#7489*# -> SECURITY CODE
*#7693*# -> You can activate & deactivate the SLEEP MODE
(when deactivated the battery will go down)
*#7787*# -> Not clear: SPURIOUS INTERRUPT
*#7948*# -> SWITCH OFF: not clear; it is a timer or something
*#8463*# -> Some information about the SLEEP MODE
Philips Genie (TCD838)
*#2337*# -> Will activate the beep signal when the cellphone reconnected to the net
Service Codes
Alcatel
Master Codes
- 25228352
- 25228353
- 83227423 (TH3/4,BH4,BF5,BG3,BF3/4..)
###337*07# - master reset (with SIM)
###847# - factory reset (with SIM)
###728# - factory reset (with SIM)
Alcatel 835 formating - **0102#
Samsung
*2767*3855# - FULL E2P RESET
*2767*2878# - CUSTOM E2P RESET
#*7337# - UNLOCK
*2767*688# - UNLOCK
*#0523# - CONTRAST
*#9998*523# - CONTRAST
*#8999*8378# - Service Menu (X100)
Philips
#20021208# ok - 630 without SIM (erase flash)
*#7728*# - RSAV DONE
*#3849*# - ??? reboot
*#3851*# - ??? reboot
Philips 568 *01763*737381# - reset
Pantech
*01763*737381# - master reset (user data, user code) without SIM
*01763*8371# - SW version
*01763*6371# - UNLOCK
*01763*3641# - Menu
Panasonic
*01763*737381# - master reset (user data, user code) A100, A101, A102,G50, G51, G70,
GD55..
*369#(*) - MENU
7, 4, 6, menu, menu - lock menu
*#9999# - 5 sec after power on - SW version (GD75, GD67, GD87..)
LG
2945#*# - service menu (code reset)(W3000 G5300 C1200 G7100...)
2945#(*)- hold (LG 500,600)
B1200 *+pwr, 6,6,8 Service Menu
B1300 *+pwr, 1,5,9 Service Menu
Security Removing Code For Lg 8110,8120.
47328545454#
Or
277634#*#
Sony-Ericsson
> * < < * < * - Service menu
< * * < - Lock menu
VK Mobile
*#79# - SW version
*#85*364# (*) - hold menu
855855# without SIM (VG107)
85558555#(*)-hold
4268#(*)-hold (VG207)
Voxtel
0124 - master code
0718#(*)- hold - menu (ST11, SC10, V100 without SIM)
4268#(*)- hold - show code (ST11, SC10 without SIM)
*789(#)- hold - menu (V50, V300, RX100 without SIM)
Motorola
(T190, T191, T205) master code
- 19980722
- 20010903
**********
P2K test menu:
*#06#, menu, menu, 048263*
Test comands:
32*116*1*0*0 - read phone code
32*118*1*0*0 - read security code
18*0 - factory reset, phone code off
18*1 - master reset
54*18*1 - full phone reset
10*0*6 - select 900/1800
32*279*1*0*8 - model
32*383*1*0*0 - flex version
Hard reset MPX200, MPX220 - blue button + power on
Nokia
*#7370925538# (valet code reset) 6230
*#746025625# [*#sim0clock#]
*#92702689# [*#war0anty#]
Fly Bird
S688 - #*301#02# send - with SIM
menu:
7 - 10 - ok,
#*8000#, #*3676# (reboot repair)
V09, S1180 - *, 3 times down, 3 times up - service menu
Enol
*#987*00# - Service menu
*#987*99# - Full reset
*#900# - SW version
Maxon
*#9922# - menu, reset (without SIM)
*#9900# - Software Version
*#9901# - Software Version (PBatch)
S60 Siries (SX1, 6600, N-Gage..)
*#7780# - factory default
*#7370# - full factory defaults (all user data reset)
SX1 formating - * + # + power on
6600 formating - 3 + * + send + power on
Sendo X1 formating - 5 + power on
Mitsubishi
*65512890 (*-hold) format FFS (Eclipse)
* 3926 - (*-hold) test mode
* 5806 - (*-hold) SW version
*(hold) 787090 - trium 320 unlock menu
Huawei (cdma)
MASTER SECURITY CODE
-309296
-3092
-9296
Pantech HX-550C (cdma)
Full reset (phone code reset)- ##03*934#9367*192#397#7412569746 PWR,
after reset - ##27732726 PWR and select "with uim"
=========================================================
Nokia Master Code Calculator, master code buat ngebuka security code
http://filecargo.com/dw.php?id=1178989260&/1/mastercode.exe
masukan imei, trus keluar dech 10 digit master code nya...
imei 15 digit bisa diliat di belakang casing dibawah battery...
ato dengan menekan *#06#
Langganan:
Postingan (Atom)
